frequency QEN62 plastic j lead smd xo ? communications equipment a pplication specifica tio n (re v -f ) electrical characteristics ...................................................... p01 mechanical characteristics ................................................... p02 ordering information ............................................................. p03 suggested reflow soldering profile ...................................... p03 tape drawing ........................................................................ p04 reel drawing ........................................................................ p04
QEN62 plastic j lead smd xo ? communications equipment application specifica tio n (rev -f) february 06 th , 2006 1 teme x r e se rv es th e r i g h t to mo di fy her ei n spe c i f i c a t i o n s an d in form a t i o n s a t any time w hen ne ce ssa r y to pr ov ide o p t im u m per form a n ce an d c o st. freque ncy electrical characteristics electrical pa rameters unit minimum ty pi c a l maximum test c onditi ons freque nc y r a nge m h z 1 6 6 . 6 6 7 outpu t logic hcmos / ttl output opera t ing te mperatu r e range (see table 1) c -10 to +70 -40 to +85 refer to ordering information storag e tem p erature range c -55 +12 5 po w e r suppl y v o ltage (vcc) v +3. 3 +5. 0 refer to ordering information frequenc y s t abilit y (see note 1) ppm 50 100 refer to ordering information aging (firs t year) ppm 5 ref at 25 c input curr en t (see tabl e 2) ma hcmos load pf 15 30 output load ttl loa d ls-ttl 1 10 refer to ordering information duty c y cle % 40/60 rise & f a ll tim e ns 8 from 10% vcc to 90% vcc start-up tim e ns 10 from 10% vcc to 90% vcc not e 1 : include 25 c tol e ran c e, op erating tempe r atur e range, input voltage cha nge (5%), load ch ang e (1 0 %), first year agin g , shock an d vibration. t a b l e 1 : stab ility co d es 5 0 ppm 100p p m -10 to + 70c b a - 40 to + 85c f d ta ble 2 : i nput curre nt vcc= 5v vcc= 3.3v fre que ncy ra nge (mhz) cl= 15 p f cl=1 5 pf 1.000 to 23.9 9 20 m a 15 m a 24.00 to 49.9 9 30 m a 20 m a 50.00 to 66.6 6 7 40 m a 30 m a
plastic j lead smd xo ? communications equipment application , 2006 QEN62 specifica tio n (rev -f) freque ncy february 06 th mechanical characteri stics bottom view s u g g e s t e d pad pin co nn ection s #1 t r i state #2 ground #3 outp ut #4 + v cc tri s t a t e func tion pin #1 output (pin # 3 ) open ac t i ve ?1? ac t i ve ?0? high z 0.52 1.52 5.08 0.25 min 7.62 4.7 max 1.27 1.27 5.8 3.0 #3 # 4 #2 #1 14.0 max 9.8 ma x 3.81 3.0 ma rk ing line 1 qen6 2 + s t a b ility / s upply v o l t a g e / outpu t c ode line 2 fre que ncy in mhz (6 digits ) line 3 da te c ode (yyww)+ma n uga c t uring c ode example for QEN62aab / 3.6864m hz line 1 : QEN62aab line 2 : 3.686 4 line 3 : 0547 -n 2 teme x r e se rv es th e r i g h t to mo di fy her ei n spe c i f i c a t i o n s an d in form a t i o n s a t any time w hen ne ce ssa r y to pr ov ide o p t im u m per form a n ce an d c o st.
QEN62 plastic j lead smd xo ? communications equipment application specifica tio n (rev -f) february 06 th , 2006 3 teme x r e se rv es th e r i g h t to mo di fy her ei n spe c i f i c a t i o n s an d in form a t i o n s a t any time w hen ne ce ssa r y to pr ov ide o p t im u m per form a n ce an d c o st. freque ncy ordering information part n u m b e rin g system QEN62 a a b 3.686 4mhz pack ag e t y p e temperature stability supply vo ltag e outp ut nomina l fre q ue ncy (mhz) smd pack ag e QEN62 : plasti c j lead smd a : 100 ppm vs -10 to +70 c b : 50ppm vs -10 to +70 c d : 100 ppm vs -40 to +85 c f : 50ppm vs -40 to +85 c a : + 5.0v d : +3.3v a : hcmos 15pf b : hcmos 30pf pleas e enter th e nomi nal freque nc y suggested reflow soldering profile
QEN62 plastic j lead smd xo ? communications equipment application specifica tio n (rev -f) february 06 th , 2006 4 teme x r e se rv es th e r i g h t to mo di fy her ei n spe c i f i c a t i o n s an d in form a t i o n s a t any time w hen ne ce ssa r y to pr ov ide o p t im u m per form a n ce an d c o st. freque ncy tape drawing item code dimension toleranc e pitc h of c o mp one nts p 12 0.1 pitc h of s p roc k e t hole po 4.0 0.1 le ngth from h o le c e n te r to c o mpone nt c e nte r p1 2.0 0.1 widt h of c a rri e r ta pe w 24.0 0.3 widt h of a dhe s i v e ta pe w0 11.5 0.1 he ight of c o m pone nt ho le a 14.65 0.1 widt h of c o mpone nt ho le b 9.60 0.1 ga p of hol d d o w n ta pe a n d c a r rie r ta pe w2 1.75 0.1 diamet er o f sp ro cket h o l e do ? 1.55 0.05 diamet er o f feed h o l e d1 ? 1.55 0.25 t o t al o f tap e th ickn ess k 5.60 0.1 reel drawing 1.5 ?20.2 ?13 25 ? 100 ?330 multiple : 1 k p c s p e r reel unit : mm
|
